2025.a Version - CYPE (2024)

New programs or modules

CYPEPLUMBING (new program)

CYPEPLUMBING combines the features of CYPEPLUMBING Water Systems, CYPEPLUMBING Sanitary Systems and Open BIM Layout. These combined applications are organised in three tabs at the bottom of the CYPEPLUMBING main window: "Water Systems", "Sanitary Systems" and "Layout". Consequently, the CYPEPLUMBING Water Systems and CYPEPLUMBING Sanitary Systems applications have been discontinued and will no longer be available in version 2025.a. However, older versions of these two programs can be downloaded from the BIMserver.center platform "Store". The Open BIM Layout application will continue to be developed in version 2025.a, as it still centralises the creation of drawings for many other applications.

  • Water Systems and Sanitary Systems tabs
    These tabs include the tools that allow users to enter and design water supply and wastewater and rainwater drainage systems, respectively. They are an improvement on the tools that were available in CYPEPLUMBING Water Systems and CYPEPLUMBING Sanitary Systems.

    Each of these two tabs is organised into three other tabs located at the top of the main window (Installation, Diagrams and Bills of quantities). These three tabs were already available in CYPEPLUMBING Sanitary Systems. CYPEPLUMBING Water Systems did not have a "Diagrams" tab, so users had to use the CYPEPLUMBING Schematics diagrams program to generate the diagrams of a water supply system. CYPEPLUMBING no longer needs to connect to another application to generate these diagrams.

    Entering an element with associated consumption and discharge in either of the two tabs means that the discharge (Sanitary Systems) or consumption (Water Systems) is automatically included in the other tab. In previous versions, the Open BIM Water Equipment program (now discontinued in version 2025.a) was required for the discharge associated with these elements to be entered in CYPEPLUMBING Sanitary Systems and the consumption in CYPEPLUMBING Water Systems (using the Open BIM workflow).

  • Layout tab
    In this tab, users can create drawings composed of the two systems (water supply and water drainage) including the graphic information imported from other applications. Specific water supply and drainage tags (not available in the Open BIM Layout application) can also be assigned and placed together with the tags that users can create in a 3D view of the drawing.

Another CYPEPLUMBING improvement is the country selection when creating a job so that the application is automatically configured with the corresponding water supply and drainage standards.

Generating native Revit® elements from a structural IFC (new module from the Open BIM - Revit Plugin)

Version 2025.a of the "Open BIM - Revit Plugin" includes a new module that allows users to convert a structural model (included in a project on the BIMserver.center platform) into native Revit elements by assigning families. The options of this module are centralised in the "Extract contents of the link and assign it to families" option in Revit's "Open BIM collaboration" menu.

To use the "Generation of native Revit elements based on a structural IFC" module, users must install the "Open BIM - Revit" plugin (which can be downloaded from the BIMserver.center platform) and have the necessary permissions in a separate CYPE license, which is purchased through an annual subscription.

As well as implementing this module, version 2025.a of the "Open BIM - Revit Plugin" is compatible with Revit versions 2021 to 2025.

More information about this new module can be found in the new feature "Generating native Revit elements based on a structural IFC".

Concrete nodes (new CYPECAD module)

CYPECAD version 2025.a includes the new "Concrete nodes" module. With this module, CYPECAD can verify the seismic design requirements to be met by the beam-column nodes of reinforced concrete frames that are part of the seismic resistance system.

More information on how this module works can be found in CYPECAD’s new feature Checking the requirements for the seismic design of reinforced concrete nodes (new CYPECAD module).

CYPE Menu

CYPE Menu. Exclusive download from the BIMserver.center platform

As of version 2025.a, the CYPE program menu can only be downloaded from the BIMserver.center platform.

The CYPE Menu application was already available from version 2024.b on the BIMserver.center platform. Now, in version 2025.a, the advantages of CYPE Menu compared to previous versions, which were downloaded from the download area of the CYPE website, are as follows:

  • As of version 2024.b
    • Once CYPE Menu has been installed, the applications it contains will be installed from this new menu when they are opened for the first time.
  • As of version 2024.f
    • CYPE Menu allows users to manage the updates of the applications it contains.
  • As of version 2025.a
    • New program groups and many CYPE applications that could only be downloaded directly from BIMserver.center are included.
    • The version of each application to be installed can be selected (from version 2024 onwards).
    • Previously installed applications can be uninstalled.

Further information on the new features can be found in the following new features of CYPE Menu version 2025.a.

In the download area of the CYPE website, the download of the program menu for versions prior to 2025.a (in 64-bit and 32-bit) will still be available. In this download area, there is also a link to the BIMserver.center platform "Store" for downloading the 2025.a version of "CYPE Menu".

As a result of these changes, the 32-bit version of the CYPE Menu is no longer available in version 2025.a. As of 18 February 2019 (version 2019.f), the CYPE programs have been running on 64-bit systems. Since then, only the classic CYPE menu could be installed on 32-bit systems. All other applications (downloadable from the BIMserver.center platform) only worked on 64-bit systems. We believe that 32-bit programming is no longer feasible to take advantage of the superior performance of 64-bit processors and operating systems. Users who still want to use certain 32-bit CYPE programs (those available in the "CYPE Menu" prior to version 2025.a) must install a version prior to 2025.a from the download area of the CYPE website, but will not be able to upgrade their programs to later versions. Please refer to our FAQ question "Which version should I download, 64-bit or 32-bit?" for more information on the 32-bit and 64-bit versions.

New groups and applications. Installing and uninstalling

In version 2025.a, CYPE Menu (which can now be downloaded exclusively from the BIMserver.center platform) has new program groups.

  • Architecture
  • Structures
  • MEP (Mechanical and Plumbing)
  • MEP (Electrical)
  • Energy and acoustic simulations
  • Project management
  • Project documents
  • Interoperability

Most of the CYPE applications are sorted into these groups. In previous versions, most of these applications could only be downloaded as single applications from the BIMserver.center platform.

By downloading and installing CYPE Menu, users will only have the CYPE programs menu installed, but none of the applications included in it will be downloaded or installed. Initially, each of the icons representing the CYPE Menu applications appears in a box with a grey background. When clicking on any of them for the first time (or on the button under the application's name), a contextual menu will appear allowing users to download and install the latest version of that application or an earlier version if available. Earlier versions (from 2024 onwards) will be available for those programs that include paid modules. Normally, free applications will only allow the latest version of these programs to be installed. Any installed version of any application can be uninstalled.

When an application has been installed, by clicking on the button under its name, the context menu that appears includes the "Uninstall" option.

More information on this program menu can be found in the FAQ "How to download and install programs from CYPE’s general menu".

The CYPE Menu download of versions before 2025 (with the applications included) is still available in the download area of the CYPE website.

New features common to CYPE programs

Quick access toolbar

As of version 2025.a, CYPE applications with a "Ribbon" have a customisable quick access toolbar (QAT), located in the top left corner of the program. This bar contains a set of commands that are separate from the active ribbon tab.

To add or remove a command from the quick access toolbar, a button has been included to access the configuration of the toolbar. Clicking it displays a window where users can add commands from the application's menus. Specific commands can be selected or all the commands found in a menu can be added using the "Assign all" button.

The list of commands added to the quick access toolbar provides options to perform the following actions:

  • Move up (move to the left) or move down (move to the right) commands in the toolbar.
  • Add a dividing line to the right of the button.
  • Remove a command or dividing line from the toolbar.

Each application can include several commands in the initial settings of the quick access toolbar and can be restored using the "Default settings" option. Furthermore, applications that are connected to the BIMserver.center platform include the "Update" and "Share" options in their default settings.

Improved options bar for entering elements in the work area

The following changes have been made to the options bar for entering elements in the work area:

  • New “Force elevation” feature
    The "2D Mode" and "3D Mode" options have been replaced by the "Force elevation" option. When the "Force dimension" option is activated, when snapping a model component, its position will be projected onto the work plane, where the new element will be inserted.
    Alternatively, when snapping a model component, the new element will be inserted at the exact position of that component, even if it is outside the working plane.
  • Viewing limits warning
    If, when entering an element in a model view, it lies beyond the visible range, a warning is now displayed in the options bar. This warning, "The point entered is beyond the limits of the view", alerts users about the position of the element beyond the visible area on the screen, allowing for a quick and accurate correction.

Element selection tool. Copy multiple times

As of version 2025.a, it is now possible to copy ("Ctrl+C") a group of elements and paste ("Ctrl+V") them in several places with the selection tool. In previous versions, the elements selected for copying could only be pasted once.

The "Element selection" tool was implemented in version 2021.e.

Link to the project owner's public profile on BIMserver.center

Now, from the BIMserver.center project information window (displayed by clicking on the project name visible in the top right bar of the application), the owner's public profile page can be accessed on the BIMserver.center platform via the link inserted in the text representing the owner's name.

Implementing codes and improving their enforcement

Rolled and welded steel structures

Implementation. SBC 306-CR 2018 (Saudi Arabia)

The Saudi Building Code for Steel Structures SBC 306-CR 2018.

Implemented in CYPE Connect and StruBIM Steel for checking bolted and welded steel connections.

Implementation. GB 50017-2017 (China)

National Standard of the People’s Republic of China: Standard for design of steel structures GB 50017-2017.

Implemented in CYPE Connect and StruBIM Steel for checking bolted and welded steel connections.

Loads on structures. Wind loads

Implementation. MS 1553:2002, AMD. 1:2013 (Malaysia)

Malaysian Standard MS 1553:2002, AMD. 1:2013. Code of practice on wind loading for building structure. AMENDMENT 1.

Implemented in Portal frame generator.

Implementation. BS 6399-2:1997 (United Kingdom)

British Standard BS 6399-2:1997. Incorporating Amendment No. 1. Corrected and reprinted June 2002. Loading for buildings – Part 2: Code of practice for wind loads.

Implemented in Portal frame generator.

Telecommunications

Implementation. UNE 133100-6 (Spain)

Infraestructuras para redes de telecomunicaciones. Parte 6: Criterios de diseño de infraestructuras de telecomunicación multioperador para nuevas urbanizaciones y reurbanizaciones.

Implemented in CYPETEL Systems.

CYPE Architecture

New tools: Extend, Trim and Fillet

CYPE Architecture's new tools in version 2025.a, "Extend", "Trim" and "Fillet" are available in the "Architecture" tab of the "Building elements" section.

These tools can be used with "Vertical elements": walls, curtain walls, lattices and railings.

  • Extend
    To extend elements, first select the element to which the others are to be extended, then select all the elements to be extended.
    Once all the elements have been selected, click the right mouse button to complete the action.
  • Trim
    To trim elements, first select the trimming element, then select the element to be trimmed, and then select the part of this element to be kept. This process can be repeated successively for all elements that intersect with the selected trimming element.
  • Fillet
    The two elements that users want to fillet are selected and the fillet will be defined automatically.

Improved use of types

In this new version of the CYPE Architecture program, important improvements have been included regarding the types that affect all the program's building elements:

  • All the elements in the job must belong to a type
    In this new version, no new elements can be created without a type. To create any new element, users must create a type for this element from the types panel of the "Architecture" tab.
    This improvement aims to ensure consistent communication with the other programs in the BIMserver.center Open BIM workflow, most of which use the building types as a base for development and analysis.
  • Type selection via a drop-down menu
    Type selection is carried out via a new drop-down menu that provides the information needed to identify the type simply. In the drop-down menu, the basic information of the type can be found, including the name of the type, an image with the colour/texture, and extra data that help identify the type.
  • Copy type
    The type creation and editing panel now has a "Copy " tool, allowing users to create a type from an existing type.
  • Automatically creating types for previous versions of jobs
    If necessary, the program will automatically create types for all those elements that are not associated with a type or for those elements that have been assigned a type that does not correspond to the description of the element.

Open BIM Site

New WMS services for obtaining maps

As of version 2025.a, Open BIM Site allows users to obtain maps via WMS services from the following data sources:

  • Spain
    • InspireBizkaia - Parcelas Catastrales y Direcciones
    • InspireBizkaia - Edificios
    • GeoAraba - Cartografía base
    • GeoAraba - Catastro
    • Gipuzkoa INSPIRE
  • Belgium
    • Federal Public Service Finance - Cadastral Layers
    • CartoWeb NGI IGN
    • Orthophotos NGI IGN
    • INSPIRE viewer NGI IGN
  • The Netherlands
    • PDOK Kadastrale Percelen INSPIRE
  • Greece
    • GeoData Orthophotos Greece
  • Argentina
    • IGN Vuelos fotogrametricos con avión
    • IGN Vuelos fotogrametricos con VANT
    • IGN Capas vectoriales
  • Mexico
    • Atlas Cibernético
    • INEGI
  • Brazil
    • MP - Ministério de Planejamento, Desenvolvimento e Gestão
  • Panama
    • IGN Tommy Guardia Datos fundamentales de la República de Panamá 2014

Plugin Open BIM - Revit

Generating native Revit® elements based on a structural IFC

Version 2025.a of "Open BIM - Revit Plugin" includes a new module that allows users to convert a structural model (included in a project on the BIMserver.center platform) into native Revit elements by assigning families. The options of this module are centralised in the "Extract contents of the link and assign it to families" option in Revit's "Open BIM Collaboration" menu.

To use the "Generation of native Revit elements based on a structural IFC" module, users must install the "Open BIM - Revit" plugin (which can be downloaded from the BIMserver.center platform) and have the necessary permissions in a separate CYPE license, which is purchased through an annual subscription.

As well as implementing this module, version 2025.a of the "Open BIM - Revit Plugin" is compatible with Revit versions 2021 to 2025.

How to use the "Generation of native Revit elements based on a structural IFC" module

After selecting the "Extract contents of the link and assign it to families" option, a dialogue box with the same name opens, which is described in detail below:

  • Main section
    All the categories of structural elements detected in the IFC links of the imported model are shown in the top left corner and are grouped by the Class and Type of IFC to which they belong. The number of existing instances and the Revit native category to be converted are also displayed from these groups.

    The categories that can be detected in this version (2025.a) are the following:

    • Walls
    • Floors
    • Structural columns
    • Structural framing
    • Structural foundation
    • Stairs
    • Ramps
    • Opening
  • Revit native family selector (Converter)
    In the highlighted red part of the image, all types are shown together with the instances of the category that have been selected in the "Main section". The existing families in the Revit template can be assigned to them and converted to native.
  • The same table allows users to create duplicates if the assigned family contains type parameters and not instance parameters ("Create duplicates" column).
  • When assigning a family with instance parameters, users must assign the parameters of the family with no need to duplicate types (users are recommended to load the families that are necessary and are not included by default in the Revit template before exporting).
  • Several filtering buttons are available to make the workflow easier for the users, allowing them to view different types of instances.
  • Converter instances/Type instances

    In the bottom part of the dialogue box "Extract contents of the link and assign it to families", the information for all the instances of the converter is displayed or, in the case of selecting a specific type, only the information for the instances of this type can be seen.

Collaborative work through a central model

In version 2025.a of the "Open BIM - Revit Plugin" a new feature has been implemented that allows users to collaborate via a central model on a local server (LAN). This feature allows the synchronisation of all previously imported IFC links from the BIMserver.center platform to the collaborative model, making it easier for other users to stay in sync with the latest version of the central model.

Sharing the Revit® model

In the "Share the Revit model" option, the "Description" field has been implemented so that users can provide a description when sharing the Revit job with a BIMserver.center project.

"About..." option

An "About..." option has been added to the "Open BIM - Revit Plugin" menu to consult the plugin information and its version.

Plugin Open BIM - Revit / Plugin MedBIM - Revit

Compatibility of CYPE plugins for Revit® with "Revit 2025"

As of version 2025.a, the CYPE plugins for Revit "Plugin Open BIM - Revit" and "Plugin MedBIM - Revit" (the latter included in the Arquimedes module "Bill of quantities of BIM models") are compatible with Revit version 2025.

Open BIM Analytical Model

Installation in German, Polish and Russian

As of version 2025.a, Open BIM Analytical Model can also be installed in German, Polish and Russian. This application can now be installed in the following languages:

  • Chinese
  • English
  • French
  • German
  • Italian
  • Japanese
  • Polish
  • Portuguese
  • Romanian
  • Russian
  • Spanish

CYPECAD

Checking the requirements for the seismic design of reinforced concrete nodes (new CYPECAD module)

As of version 2025.a, CYPECAD verifies the requirements for the seismic design to be met by the beam-column nodes of reinforced concrete frames that are part of the seismic force resisting system.

These checks for reinforced concrete nodes have been implemented for the following codes:

  • ACI 318-08
  • ACI 318-11
  • ACI 318-14
  • ACI 318-19
  • NSR-10 (Colombia)
  • NTRC-17 (Mexico)
  • NB 1225001-1:2020 (Bolivia)
  • Eurocode 8
  • Spanish structural code "Código Estructural"

In the "Columns/Shear walls" menu of the "Results" tab, there is a new option: "Concrete nodes - Consult checks" which allows users to consult all the checks carried out in the selected node.

This option also allows users to access the corresponding editors, if necessary, in order to modify the reinforcement of the beams and columns at the node.

The "ULS checks" report has been extended with the corresponding tables summarising the status of the checks of the concrete nodes.

If not all checks are met at a node, a corresponding warning is displayed in the final analysis report, similar to the errors and warnings for other elements.

Job templates

In the "File" menu of CYPECAD version 2025.a, the "Save as template" option has been added.

This new option allows the configuration and general data of a job to be stored in templates and used later when creating new jobs.

Saved templates can be used when creating a new job by selecting the "Start from a template" option.

Concrete cover in beams per frame

In CYPECAD version 2025.a, it is now possible to define concrete covers in beams that are different from those entered in the general data of the job.

To do this, in "Beam Definition > Beams > Other options > Assign covers" tab, the "Specific for the beam" option can be selected.

Predefined loads

In the options for entering loads on the floor ("Loads", "Line loads on beams", "Surface loads on slabs"), the possibility of predefining these loads has been added so they can be entered more easily.

Furthermore, if any changes are made to the value of the load, they will be much quicker and there will be less chance of mistakes.

Reference search

In CYPECAD version 2025.a, the "Groups-Search references" option has been added.

This allows users to search for elements (columns, walls, frames, slabs, beam intersections and predefined loads) by their reference.

Only the reference, or part of it, needs to be entered for the element to be located.

Beams and slabs can also be searched for with the "Beam 1" ("Slab 1") format.

Copying punching shear reinforcement from one floor to another

This new feature in version 2025.a of CYPECAD makes it possible to copy the punching shear reinforcement defined for one support to the same support located on another floor.

Bill of quantities of punching shear studs

As of version 2025.a, the quantities of PSB® punching shear studs manufactured by Peikko, as well as user-defined generic studs, are already exported when generating the structure's bill of quantities.

Other improvements and corrections

CYPECAD version 2025.a includes the following program improvements and corrections for some specific cases:

  • The display of the geometry of the beams in 3D and their export has been improved. Several cases have been solved where they overlapped with columns. This is still done in cases where the beam has a part that is not in contact with the column.
  • The "Edit groups-Construction process" has been improved. Now, when selecting more than one group in the list, the edited values in all selected groups are modified.
  • An error that could occur after moving columns with fanned-out studs as punching shear reinforcement if the layout of the studs in the new position could not be obtained, has been fixed. Now, in this case, the definition segment marked in red is shown.
  • The "Groups-Copy group elements" option has been improved. Previously, if any elements were entered via "Edit resources", they were copied even if the "Copy edit resources" option was not selected.
  • An error that occurred when performing the punching shear checks in a case where beams failed to intersect near the support has been fixed.
  • An error that occurred in the process of obtaining the centre of stiffness and the centre of masses when analysing a job with an integrated 3D structure in which rigid diaphragms are defined, has been solved.
  • An error in the design of footings has been fixed. This could occur in the case of a rectangular footing when "Make square" was selected in "Direction of growth".
  • There has been an improvement in the entry of editing features in the beam portal frame editor.
  • The elements of the portal frame can now be snapped.
  • An error that occurred when a concrete wall was inserted and this generated a new panel, if the wall had the "Shear wall" option checked, has been fixed.
  • An error that systematically occurred when obtaining the force report for composite slabs has been fixed. This error occurred in version 2024.f due to changes made in the generation of reports.
  • The time for generating the bars of beam portal frame reinforcement for the 3D view with detailing and for exporting this reinforcement has been significantly reduced. In future patches, the time for generating the bars of other types of elements will also be reduced.

CYPE 3D

Selecting surfaces exposed to fire in steel sections and timber bars

In CYPE 3D version 2025.a, we have implemented the selection, by bar, of the surfaces exposed to fire, in steel sections and timber bars.

In the "Bar" menu, the "Fire resistance" option can be used to assign the exposed surfaces to the selected bars. This option will be active when users have selected the "Check fire resistance" option in "General data".

For steel sections, users can choose any of the predefined options from the drop-down button, in which the program automatically determines the form factor based on the exposed surfaces; or select the last option, where they manually enter the form factor and the number of exposed surfaces.

For rectangular section timber bars, users may decide whether or not each of the four surfaces of the section is exposed to fire.

Up until version 2025.a, the program would conservatively consider all exposed faces.

With this new feature, users will be able to optimise the thickness of the protective coatings as well as the sections of the bars when the faces of the bars are not exposed to fire.

Selecting intumescent paints by manufacturer

In version 2025.a, intumescent paints from manufacturers' catalogues have been incorporated.

Under "General data > Fire resistance", when selecting "Check fire resistance" for steel sections, the type of protective coating can also be selected.

By selecting "Intumescent paint" the available catalogues can be used.

The thickness of intumescent paint required for the protection of each bar is obtained from the selected catalogue, based on the estimated critical temperature, the shape factor, the number of exposed sides and the type of structural element (column or beam).

From the "Bar" menu, under "Fire resistance" it is possible to assign the type of structural element, either a column or a beam, to each bar. By default, the program assigns the first option, which automatically determines whether it is a column or a beam, depending on the angle formed by the bar with the horizontal plane.

Installation in Romanian

As of version 2025.a, CYPE 3D can also be installed in Romanian. This application can now be installed in the following languages:

  • Bulgarian
  • Catalan
  • English
  • French
  • Italian
  • Polish
  • Portuguese
  • Romanian
  • Russian
  • Spanish

Portal frame generator

Installation in Russian and Romanian

As of version 2025.a, Portal frame generator can also be installed in Russian and Romanian. This application can now be installed in the following languages:

  • Bulgarian
  • Catalan
  • English
  • French
  • Italian
  • Polish
  • Portuguese
  • Romanian
  • Russian
  • Spanish

CYPE Connect / StruBIM Steel

Groups of operations

As of version 2025.a, the CYPE Connect and StruBIM Steel connection editors allow users to sort the list of operations including groups of operations.

In the operation list options bar, there is a "New group" option for adding groups. This option adds a new empty operation group.

When a group is selected, new operations are added within that group.

To move an existing operation into or out of a group, the tools must be used to move it up or down, depending on the position. Operations can also be dragged and dropped into or out of a group.

Groups of operations can be collapsed or expanded, to display or hide the operations they contain.

The activate or deactivate option, located to the left of each group's name, affects all the operations it includes. A group of operations can be activated or deactivated by clicking on the option.

Pressing the "Copy" option with a group selected copies the group with all its operations.

The "Delete" option allows users to delete the group and all the operations it contains, or to delete the group and keep the operations ungrouped.

If a group is selected, the "Export selected operations to the library" option exports all the operations contained in that group.

Improved operations list

Version 2025.a includes the following options and improvements to the operations tree:

Drag and drop
This feature allows users to select, move and drop operations or groups of operations to another position. With this new tool, an operation can be moved to the desired position without having to go through the intermediate positions one by one.

Icons
The operations list includes an identifying icon for each operation in the list.

Move to the top
Moves the selected operation or group to the top of the list.

Move to the end
Moves the selected operation or group to the end of the list.

Search
Allows users to search for operations by text.

Delete all the elements in the list
Deletes all operations and groups of operations from the list.

Improved use of data entry tables

Up until version 2025.a, in order to paste information from the clipboard into the data entry tables, these tables needed to have several rows greater than or equal to that of the source table to be pasted. Therefore, only the information in the rows of the table was copied, without adding new ones.

As of version 2025.a, when pasting tables from the clipboard, if the number of rows of the source table is larger, the number of rows needed to paste the whole table will be created.

StruBIM Uploader

Installation in Chinese and Turkish

As of version 2025.a, StruBIM Uploader can also be installed in Chinese and Turkish. This application can now be installed in the following languages:

  • Catalan
  • Chinese
  • English
  • French
  • German
  • Italian
  • Japanese
  • Polish
  • Portuguese
  • Romanian
  • Russian
  • Spanish
  • Turkish

StruBIM Shear Walls / StruBIM Uploader

Updating the reading of XML files generated with ETABS®

Up until version 2025.a, the reading of XML files produced with ETABS® for shear wall design in StruBIM Shear Walls supported ETABS 2016 and ETABS 18. The XML file can be imported directly into StruBIM Shear Walls or via the StruBIM Uploader.

As of version 2025.a, the reading of files produced with ETABS version 21 is also supported.

Installation in Chinese and Turkish

IFC Builcer

Options bar for the layout of the model components

As of version 2025.a, IFC Builder and the applications that include the "3D Model" tab have an options bar for the layout of the model components, the same as the one available in applications with a 3D environment.

This way, the tools related to the entry of the new element are anchored below the application's toolbar.

Element selection tool

As of version 2025.a, IFC Builder and the applications that include the "3D Model" tab have the element selection tool.

This feature is available when none of the application's own options have been activated and allows multiple actions to be carried out on the elements entered in the work area.

CYPELEC / CYPELEC Core

Combining the CYPELEC Core, CYPELEC REBT, CYPELEC NF and CYPELEC RETIE programs

As of version 2025.a, the CYPELEC Core, CYPELEC REBT, CYPELEC NF and CYPELEC RETIE programs are combined into a single program called CYPELEC.

When starting the CYPELEC program, a selection window appears in which the user must select the option corresponding to the code to be applied in the design of the low-voltage electrical system.

CYPELEC allows users to open jobs from previous versions of CYPELEC Core, CYPELEC REBT, CYPELEC NF and CYPELEC RETIE.

2025.a Version - CYPE (49)

Creating views

To make it easier to view the diagram, views of the single-line diagram have been added.

The "Views" group is located on the left-hand side of the interface and will always include the "MAIN" view, which corresponds to the complete single-line diagram.

The procedure for creating a new view can be started by clicking on the "Create a view based on the selected line" icon. Then the line is selected from which a partial view of the diagram is to be generated. The new view will appear in the list and can be selected for detailed viewing.

The list of views created can then be used to generate the drawings. To do this, select the "By views" option in the "Detail of the single-line diagram" option of the "Drawing editor" dialogue box.

CYPELEC Electrical Mechanisms

Improvement in the new job creation assistant

The following sections have been included in the new job creation assistant:

  • Regulations
    Selecting the regulations to be applied.
  • Catalogues
    Selecting the manufacturer's catalogues.
  • Spaces
    Configuring spaces if the BIM project contains them.

CYPELEC Distribution / CYPELEC Electrical Mechanisms

Direct reading of the symbols

CYPELEC Distribution displays the symbols used in CYPELEC Electrical Mechanisms without having to enter them again. To do this, when the job is created in CYPELEC Distribution, it must be linked to a BIM project containing information from CYPELEC Electrical Mechanisms.

These symbols are transferred as a template in DWG format so that they can be deactivated in the "Template views manager".

CYPETEL Systems

New 3D work environment

As of version 2025.a, developing telecommunications infrastructures in CYPETEL Systems can be carried out in a 3D work environment.

The elements and conduits of the installation can be included via the "3D view" or the different work planes. Each element type corresponds to a model layer, and its visibility can be activated or deactivated independently. It has a 2D display mode for the elements to make it easier to interpret them in the drawings exported by the program.

The program allows users to continue working on 2D templates from the BIM model or imported from the program in DXF, DWG, and DWF formats, as well as in various image formats (JPEG, JPG, PNG or WMF). This way, working compatibility is maintained in projects that do not have a 3D architectural model.

The reading of jobs produced with previous versions of the program will not be affected by this modification.

Thanks to this new 3D environment, which allows contributions of urban area maps from Open BIM Site to be displayed, and to the implementation of the UNE 133100-6 standard in this version 2025.a, users can carry out urban infrastructure deployment projects for telecommunications networks in CYPETEL Systems.

AcouBAT by CYPE

Updated acoustic testing database

The acoustic testing database associated with the AcouBAT analysis engine (managed by the French organisation CSTB - Centre Scientifique et Technique du Bâtiment) included in the application has been updated.

The number of products available has been increased with more than 400 new references from the following manufacturers:

  •  ACO
  •  ARCELOR
  •  ARTIGO
  •  DECAYEUX
  •  DECEUNINCK
  •  EUROBLOCK
  •  FABEMI
  •  GIACOMINI
  •  PRB
  •  SOUCHIER

During the database upgrade process, when running the new version of the application for the first time, the customised products previously created shall be saved.

CYPEFIRE Pressure Systems

New 3D work environment

As of version 2025.a, the design of pressurisation systems in CYPEFIRE Pressure Systems will be carried out using a three-dimensional work environment.

Now, the leaks produced in the different building elements (doors, windows or partitions), in addition to the pressurisation system, can be included via the "3D view" or the different work planes. Each of the element types corresponds to a layer of the model, which can be activated or deactivated independently.

The program allows users to keep working on 2D templates from the BIM model or imported from the program in DXF, DWG, DWF formats; or in various image formats (JPEG, JPG, PNG or WMF). This way, working compatibility is maintained in those projects that do not have a 3D architectural model.

Jobs created with previous versions of the program can no longer be read, so it is recommended to use version 2024.f to continue working with this version.

Data entry wizard

The data entry wizard is used to classify the project spaces in order to generate a staircase pressurisation system according to class and leakage.

The wizard will assist users in collecting the geometrical data of the staircase to quickly obtain all the leaks produced and to obtain the result with greater ease.

The option to enter all information manually or even to make minor modifications to the pressurisation system generated by the wizard is still available.

Selecting the pressurisation systems

Now, in version 2025.a, CYPEFIRE Pressure Systems can be used to download staircase pressurisation system manufacturers' catalogues in order to select the systems and complete the design of each of the systems entered.

Once the analysis has been carried out, users can select the system that best meets their needs from the list of systems and perform a graphical check to ensure that it meets the designed requirements.

CYPEHVAC

Implementing direct expansion systems (VRF, multi-split, split 1x1 and air-source heat pumps)

As of version 2025.a, there is an extension to the types of air conditioning systems that can be designed in the program. As a result, the following direct expansion systems have been added to the program: VRF, multisplit and 1x1 splits. Air-source heat pump systems have also been added as generators for water-based air-conditioning systems.

New management of equipment manufacturers and libraries

As of version 2025.a, the program divides the management of equipment and products that can be selected for the system design into library elements and manufacturer elements:

For manufacturer elements, the program allows users to download catalogues with all the data necessary for the design, via the connection to the Open BIM Database. The control of the downloaded catalogues is carried out from the "Catalogue management" option in the program:

Tab rearrangement

As a result of the integration of new air conditioning systems in the program and in order to make its use easier, the presentation of the toolbars has been reorganised by joining them together in a single tab for all the elements of the system, and with the existing "Bill of quantities" tab. This way, users have all the elements needed to design the system, whatever type it may be, in the same tab.

Changes in the management of imported thermal loads

This version of CYPEHVAC slightly modifies the management of the relationships between the imported thermal loads and the terminal elements of the system. Now, the parameters of the terminal units include the "Assigned thermal loads", i.e. the loads to which they will contribute their power and from which the power requirements to be contributed and design temperatures will be extracted:

The program allows users to import thermal loads from the BIM model, in which case they will have an associated geometry and the program will allow them to be associated to the units automatically, by means of their layout. But, as a new feature, it will also allow them to be created without associated geometry with the "Thermal loads" option in the tools menu. In this case, the users will have to associate them to each unit with the "Assign thermal loads" option:

New pre-installation node and duct covers

A new element has been added to the duct layout design tools that allows users to indicate the start of the system, in case they want to design a duct system without specifying the starting machine.

Furthermore, the duct installation is completed by automatically including sealing surfaces at the ends of the ducts, if required.

Installation in Chinese, German and Turkish

As of version 2025.a, CYPEHVAC can also be installed in Chinese, German and Turkish. This application can now be installed in the following languages:

  • Catalan
  • Chinese
  • English
  • French
  • German
  • Italian
  • Polish
  • Portuguese
  • Romanian
  • Russian
  • Spanish
  • Turkish

IFC Builder / CYPE Construction Systems / CYPETHERM LOADS / CYPEFIRE FDS

Punctual thermal bridges and linear thermal bridges

As of version 2025.a, it is possible to enter "Punctual thermal bridges (per m²)" and "Linear thermal bridges" in the "Thermal insulation" tab of the "Technical data" window for the following categories of construction systems:

  • Façades
  • Party walls
  • Basement walls
  • Partitions
  • Roofs
  • Exterior floor slabs
  • Intermediate floor slabs
  • Screeds

Thermal simulation applications can read and incorporate the properties of contributions from IFC Builder and CYPE Construction Systems into their design models.

Furthermore, applications with a "3D Model" tab (CYPEFIRE FDS and CYPETHERM LOADS) can obtain data directly from the construction systems defined in the geometric model.

Overall technical data for "Thermal insulation" in windows and skylights

As of version 2025.a, an overall "Thermal transmittance" value can now be defined for windows and skylights as an alternative to the "Glazing" and "Fittings", which has been the case up to now. For this purpose, the "Thermal characterisation of the element" option has been added to the "Thermal insulation" tab of the window "Technical data" in the following construction system categories:

  • External windows
  • Interior windows
  • Exterior skylights
  • Interior skylights

Thermal simulation applications can read and incorporate these properties of the contributions from IFC Builder and CYPE Construction Systems into their design models.

Furthermore, applications with a "3D Model" tab (CYPEFIRE FDS and CYPETHERM LOADS) can obtain data directly from the construction systems defined in the geometric model.

CYPETHERM LOADS

Installation in German, Romanian, Russian and Turkish

As of version 2025.a, CYPETHERM LOADS can also be installed in German, Romanian, Russian and Turkish. This application can now be installed in the following languages:

  • Catalan
  • Chinese
  • English
  • French
  • German
  • Italian
  • Polish
  • Portuguese
  • Romanian
  • Russian
  • Spanish
  • Turkish

CYPEURBAN

Improved space import assistant and dwellings import assistant

In CYPEURBAN version 2025.a, the operation of these two assistants has been optimised:

Space import assistant
The improvements of this assistant are described in detail in this version's new feature Space import assistant.

Dwellings import assistant
The dwellings import assistant allows users to import the dwellings defined in the IFC file of the project by means of spaces (IFCSpace) or groups of spaces (IFCGroup). This assignment is done manually through the parameters and values of the IFC.

CYPEURBAN / CYPELEC Electrical Mechanisms

Space import assistant

The space import assistant allows users to classify the spaces in the project's IFC file according to the specific types in each program.

If values similar to the specific types in the program are found in the space descriptions in the IFC file, the assignment table is automatically completed with the types found.

Furthermore, this assignment can be done manually through the parameters and values of the IFC. Once the values in the assignment table have been imported, a specific type from the program must be indicated for each of the values.

  • Importing spaces via an IFC parameter
    Using the blue arrow available in the toolbar, users can manually import the spaces according to the parameters available in the IFC: Name, TypeName, LongName, PSET, etc. Selecting the parameter will import all the values associated with that parameter in the mapping table.
  • Importing a space via an IFC value
    Using the "+" button available on the toolbar, users can import a space individually. The process is similar to the one described above but in this case, instead of importing all parameter values, users can select a specific value to be imported.

Discontinued programs

CYPEPLUMBING Water Systems / CYPEPLUMBING Sanitary Systems / CYPEPLUMBING Schematics diagrams / CYPEPLUMBING Solar Systems / Open BIM Water Equipment. Discontinued programs

Starting with the 2025.a version of CYPE programs, the following applications will no longer be available:

  • CYPEPLUMBING Water Systems and CYPEPLUMBING Sanitary Systems
    The features of these two programs are combined in CYPEPLUMBING (new application implemented in version 2025.a). Users can now design water supply systems, wastewater and rainwater drainage systems and create their drawings in the same program. Learn more about the advantages of this new application implemented in version 2025.a in CYPEPLUMBING.

    Version 2024.f of CYPEPLUMBING Water Systems and CYPEPLUMBING Sanitary Systems can still be downloaded from the BIMserver.center platform.

  • CYPEPLUMBING Schematics diagrams
    The features of this application (automatic generation of the schematic diagram of a water supply system using the BIM connection with CYPEPLUMBING Water Systems) become part of CYPEPLUMBING in version 2025.a; and can be found in the main CYPEPLUMBING window, specifically, in the "Diagrams" tab located at the top and which appears when the "Water Systems" tab located at the bottom is selected. In CYPEPLUMBING you can find out about the advantages of this new application implemented in this version 2025.a.

    Version 2024.f of CYPEPLUMBING Schematics diagrams can still be downloaded from the BIMserver.center platform.

  • CYPEPLUMBING Solar Systems
    This application will no longer be generated in version 2025.a. However, the CYPEPLUMBING Solar Systems download version 2024.f is still available on the BIMserver.center Store so that users can continue to design solar thermal systems for domestic hot water or heating. In versions after 2025.a, the features of this program will become part of CYPEPLUMBING.
  • Open BIM Water Equipment
    The equipment that could be entered by this application can continue to be entered from CYPE Architecture, and the consumption and discharge values of each unit are automatically entered in CYPEPLUMBING when a consumption or discharge system is positioned.
2025.a Version - CYPE (2024)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Kelle Weber

Last Updated:

Views: 6065

Rating: 4.2 / 5 (53 voted)

Reviews: 84% of readers found this page helpful

Author information

Name: Kelle Weber

Birthday: 2000-08-05

Address: 6796 Juan Square, Markfort, MN 58988

Phone: +8215934114615

Job: Hospitality Director

Hobby: tabletop games, Foreign language learning, Leather crafting, Horseback riding, Swimming, Knapping, Handball

Introduction: My name is Kelle Weber, I am a magnificent, enchanting, fair, joyous, light, determined, joyous person who loves writing and wants to share my knowledge and understanding with you.